List of Contributions

servando lizardi

Contact Details

servando lizardi


My Content

1 to 13 of 13 total
Posted By servando lizardi Dec 09, 2024 09:07:00 AM
Found In Egroup: General Discussions
\ view thread
Good morning, everyone would be possible to share to me an information of PLC 5 of Allen Bradley, some examples, what kind of software to stablish communication an upload the file. best regards. EDIT: moved to Legacy community -FL
Posted By servando lizardi Nov 01, 2024 10:16:10 AM
Found In Egroup: Legacy
\ view thread
thanks too much for your recommendations, controller was fix and runs well, I got a good experience to this controller. best regards. machine run since 10/18/2024 non interruptions just stop for change over. best regards.
Posted By servando lizardi Oct 15, 2024 08:16:00 AM
Found In Egroup: Legacy
\ view thread
Good morning, could you please help to me to literature for GML Commander software, how to clear some fault for the 1394T GMC Turbo controller.. fault status 7. normally use '' '' and reset the controller but the driver not clear the fault...
Posted By servando lizardi Oct 10, 2024 07:44:01 AM
Found In Egroup: Legacy
\ view thread
Thanks too much; the servo drive will send to refurbish, thanks too much for your time, was helpful, best regards.
Posted By servando lizardi Oct 09, 2024 01:48:10 PM
Found In Egroup: Legacy
\ view thread
Good afternoon: I made the master reset as your recommendation; and the servo drive accept the script, machine was run 5 cycles and then abort the program, and status LED appear on MEMORY FAULT; after that a download the script and servo drive is FAULT I mentioned before, any recommendation for memory ...
Posted By servando lizardi Oct 09, 2024 08:39:20 AM
Found In Egroup: Legacy
\ view thread
Good morning thanks for your help and literature, the servo controller is in mode of checksum memory failure; I followed the procedure for re-initializing; press master reset button and init button; but the cpu still in checksum error... What would be the cause to controller is damaged? any recommendation ...
Posted By servando lizardi Oct 07, 2024 01:47:00 PM
Found In Egroup: Legacy
\ view thread
Good afternoon, everybody, today we have a problem to solve with a 1394 servo-controller, I download the back up SCRIP, but on this time was aborted the scrip, send an error as show below; for this problem what would be the correct way to solve to accept to download.... Any help would be helpful. ...
Posted By servando lizardi Aug 20, 2024 09:41:24 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products
\ view thread
Tanks too much for your time and support my friend; I will double check the ground screws, for the question 1 y 2 you made.... is not new installation the machine has 3 servos axis work simultaneously...... the servo drives are connected to a UPS EATON BACKUP Battery: 220v ac single phase.... For the ...
Posted By servando lizardi Aug 19, 2024 02:33:00 PM
Found In Egroup: Drives, Motion Control & Low Voltage Products
\ view thread
Hi everyone, I hope someone help to me to understand why appear the fault of DCBUS and how to eliminate it, the FAUL S25 SAID.... " The pre-charge circuit monitoring algorithm detected that the DC BUS did not reach a factory set voltage level after charging for a period of time" help to understand ...
Posted By servando lizardi Jun 20, 2024 11:48:00 AM
Found In Egroup: Automation Control
\ view thread
Hi everyone; somebody have an instruction document to help me, I have a chance to protect some displays to avoid the access, just only personnel authorized, I new on the FTView editor help please. best regards.
Posted By servando lizardi Mar 01, 2024 01:02:00 PM
Found In Egroup: Installation & Activation
\ view thread
thanks too much!.
Posted By servando lizardi Mar 01, 2024 12:54:00 PM
Found In Egroup: Installation & Activation
\ view thread
Good afternoon, folks! I have a problem with my old laptop is dean and was not able to rehost the products key, how someone guide to me to activate the product key on my new laptop? best regards.