List of Contributions

Matt See

Contact Details

Matt See


My Content

1 to 20 of 27 total

RE: Electronic starter failure E300.

Posted By Matt See Sep 25, 2025 04:40:07 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Great suggestions @Philip Hamilton. Gomes - please also refer to QA24390 Access Level: Everyone. E300 Electronic Overload: Clearing a Non-Volatile Storage Fault ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain Expert ------------------------------

RE: PowerFlex 520 series FLA min

Posted By Matt See Oct 15, 2024 10:38:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hello @Say Here is a technote discussing this recommendation in more detail. Note that you will need a TechConnect contract to view it: Drive to Motor Size Ratio Recommendation: PWM AC Drive ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain Expert ...

RE: No Response to Tickets

Posted By Matt See Aug 16, 2024 05:28:00 AM
Found In Egroup: Installation & Activation \ view thread
Hello Michael, Sorry for the delays you've been experiencing. I have reached out to you privately, by email, to try and help. ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain Expert ------------------------------

RE: E300 Emulation mode

Posted By Matt See Aug 12, 2024 10:20:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hi @Dan Mos By way of a follow-up, please find an article on our knowledgesbase that dicusses this in more detail: https://rockwellautomation.custhelp.com/app/answers/answer_view/a_id/1089513 ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain Expert ...

RE: Can I read current and voltage values per phase on the drive output?

Posted By Matt See Aug 12, 2024 09:31:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hi @Splash By way of a follow-up, please see this technote that discusses the limitations of this feature. I've just edited the technote to make it easier to find. ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain Expert --------------------- ...

RE: P309 - % Motor Flux Displays in PowerFlex 700S2

Posted By Matt See May 22, 2024 09:07:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hi @Valverde, Just closing the loop here...please find linked below a couple of technotes on our knowledgebase. Whilst they are not necessarily aimed aimed at your particular drive, they may prove useful as background information. A TechConnect contract is required, to view: PWM AC Drive: ...

RE: Kinetix 5300 drive Faulted

Posted By Matt See May 21, 2024 10:48:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hello Ryan, Thanks for spotting this. I have reset the access level to "Everyone". The technote contains information that exists in the public domain, and no TechConnect-only content. ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain ...

RE: PF753 Decel Inhibit Fault while running

Posted By Matt See May 21, 2024 10:09:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hello McCarthy, Just closing the loop here. We have some great guidance on knowledgebase on Decel Inhibit: PowerFlex 70, 700, 750-Series, and VTAC9 Drives: F24 [Decel Inhibit Fault] ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain Expert --- ...

RE: Kinetix 5300 drive Faulted

Posted By Matt See May 21, 2024 09:31:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hi @Arleybarc, For future, the list of Kinetix 5300 fault codes can be found on our knowledgebase here: Kinetix 5300 Fault Codes ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain Expert ------------------------------

RE: PF753 fault code 168

Posted By Matt See May 20, 2024 10:42:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hello @Fells Just closing the loop here - the anomaly is discussed in more detail in the following technote: PowerFlex 750-Series AC Drives: Fault F168 HeatSinkUnderTmp ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain Expert ---------------- ...

RE: powerflex 4 deceleration

Posted By Matt See May 20, 2024 09:38:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Good to hear! Best wishes for a successful application of your equipment. ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain Expert ------------------------------

RE: powerflex 4 deceleration

Posted By Matt See May 20, 2024 09:24:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hi @hasak Just closing the loop here, and linking the following technote that may be of further help: PowerFlex 4/5 Series Drive - Decelerate Slower Than Programmed / Disable Bus Regulator Regards ------------------------------ With kindest regards, Matt See Consultant ...

RE: Kinetix drives to profibus network

Posted By Matt See Apr 25, 2024 10:33:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hi @Mihajlo Baić Just closing the loop here. The knowledge has been captured and added to our Knowledgebase (access level TechConnect) QA75954 - Using Kinetix CIP Motion drives on Siemens S7 controller ------------------------------ With kindest regards, Matt See Consultant Knowledge ...

RE: How to run two axis (servos Kinetix 5500) simultaneously on studio 5000?

Posted By Matt See Apr 25, 2024 10:21:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hi @Eufrasio Just closing the loop here. The knowledge has been captured and added to our Knowledgebase (access level TechConnect) QA75957 - Moving two Kinetix axes simultaneously ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain Expert ...

RE: Powerflex 4 AC Drive: Current Limit setpoint A089 Parameter question

Posted By Matt See Jan 11, 2024 11:12:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Good day, By way of follow-up, please find a link to a technote on this topic (access level = Tech Connect): PowerFlex Drive will not get to commanded speed ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain Expert ------------------------ ...

RE: Kinetix 5700 servo drive with Parker MPW motor compatibility?

Posted By Matt See Jan 09, 2024 09:50:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hi Laforge, Just closing the loop here, this knowledge has been captured, and added to our Knowledgebase (access level = Tech Connect) QA67421 - Kinetix 5700 compatibility with Parker MPW 142 Servo Motor ------------------------------ With kindest regards, Matt See Consultant ...

RE: Kinetix 5700 + 2198+P070 Overload

Posted By Matt See Jan 09, 2024 08:23:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hi Joshu, By way of further information, please find linked knowledge here (access level = Tech Connect): Kinetix 5700 inverter utilization ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain Expert ------------------------------

RE: Kinetix 5300 SC05 error

Posted By Matt See Jan 08, 2024 10:40:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hello Ananja, By way of further information, please find a link to a related article on our knowledgebase (access level = Tech Connect) Kinetix Drives: Safe Torque Off Recovery for CIP Axes ------------------------------ With kindest regards, Matt See Consultant Knowledge Domain ...

RE: can I change the direction of a PowerFlex 70 using a digital input?

Posted By Matt See Jan 08, 2024 09:02:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hello Paul, By way of additional information, please refer to the following technote on our knowledgebase (access level = Everyone) PowerFlex 70 and 700 drive direction control Regards, Matt ------------------------------ With kindest regards, Matt See Consultant ...

RE: Armor PowerFlex to 450L Light Curtain cabling.

Posted By Matt See Dec 18, 2023 06:20:00 AM
Found In Egroup: Drives, Motion Control & Low Voltage Products \ view thread
Hello Bouteiller! I've reviewed your query, and given the nature of the enquiry, a Remote Support service ticket has been created, as you have a Tech Connect contract in place for the product line in question. You will be contacted by the team in due course. ------------------------------ ...